过程能力中文.xls

SPC输出报告 Capture Capture.Capture Capture.Capture ResetValues 下限能力指数Lower capability index (CPL) 能力指数Capability index (Cp) 能力比值Capability ratio (CR) 样本标准差Std Deviation (n-1) 标准差Std Deviation (n) 样本方差Variance (n-1) 方差Variance (n) 性能指数Performance index (PP) 性能比值Performance ratio (PR) 地点LOCATION 零件PART 设备TOOL 尺寸DIMENSION (备 注)： 01 PSW!H6 01 PSW!A14 01 PSW!A6 01 PSW!A8 01 PSW!D10 01 PSW!A21 Class 07 CAV!A6 AJ04 PPU AJ05 PPL AJ06 AJ07 AJ08 AJ10 AJ11 AJ12 AJ13 AJ14 AveX UCLx Min LCLx Max D11 AveR UCLr Diff M11 Data Values LCLr XGoUP XAcumUP XAcumDw XMaxUP AF29 XMaxDown AF30 XHMUps XHMDws RGoUP RAcumUP RAcumDw RMaxUP AF36 RMaxDown AF37 RHMUps RHMDws sample # Above UCLx AJ16 Below LCLx AJ17 Above UCLr AJ18 Below LCLr AJ19 XAbove XBelow RAbove RBelow XACounter n XBCounter RACounter RBCounter MaxXA MaxXB Average MaxRA Range MaxRB N O T E To chart: Data X ADDING 工厂 零件图号 零件名称 部门： 规范值 量具编号Tool number 量具名称Description 数据点重要趋势Significant trends of data points: 上升Increasing 下降Decreasing 超出控制限Out of control limits 次数HOW MANY RUNS 趋势长度RUN LENGTH X 图Chart R 图Chart 读数数目Number of readings 规格下限Lower spec limit (LSL) 规格值Nominal 规格上限Upper spec limit (USL) 总和Total sum 平均值Average readings ( X ) 最大值Maximum 最小值Minimum 低于规格下限的读数Readings below LSL 高于规格上限的读数Readings above USL 极差均值Average Range (R) N= D2 值Value 上限能力指数Upper capability index (CPU) 正公差PLUS 负公差 编制： 校对： 编制日期 产品型号 AJ09 UCLx 点连续在均值中心线之上consecutive data points above average X 点连续在均值中心线之下consecutive data points below average X 点连续在极差中心线之上consecutive data points above average R 点连续在极差中心线之下consecutive data points below average R 初始过程能力不足- 均值有向上的趋势- Trend UP (X) - 均值有向下的趋势Trend DOWN (X) - 均值超出控制限Out of control limits (X) - 极差有向上的趋势Trend UP (R) - 极差有向下的趋势Trend DOWN (R) - 极差超出控制限Out of control limits (R) - 过程变异Proc. variation (Pp not 1.67) - 过程不集中或能力不够Proc. not centered/capable (Ppk not 1.67) - 过程能力不足，需要提高Process substandard, needs improvement (PPk1.33). 均值超过7点连续在中心线之上More than 7 consecutive points above X 均值超过7点连续在中心线之下Mor