过程能力研究样表.xls

跳动度(4) 跳动度(3) 跳动度(2) 跨棒距 跳动度（1） 台阶 Capt Capt.GoA1 Capt.GoA1 Capt.GoA1 Capt.GoA1 Capt.GoA1 Capt.GoA1 Capt.GoA1 Capture Capture Capture Capture Capture Capture Capture Capture.Capture Capture.Capture Capture.Capture Capture.Capture Capture.Capture Capture.Capture Capture.Capture GoA1 GoA1 GoA1 GoA1 GoA1 GoA1 GoA1 ResetValues ResetValues ResetValues ResetValues ResetValues ResetValues ResetValues CPK PROCESS CAPABILITY CERTIFICATION REPORT .00 PROCESS IS CAPABLE (see if any notes are on page 2) PROCESS IS CAPABLE Part Certification Number of readings per subgroup 5.00 P R O C E S S I N F O R M A T I O N 1.00 1.00 01 PSW!A21 07 CAV!A6 01 PSW!H6 01 PSW!A6 01 PSW!A14 01 PSW!D10 01 PSW!A8 Significant trends of data points: X Chart R Chart X bar Lower R Upper R 8.00E-03 6.00E-03 .01 1.00 AJ04 1.00 -.04 -.04 -.03 .00 AS04 .00 AA3=0 if none LOCATION Plant 宁波市鄞州甬乐机械部件厂 Dept: quality dept. Date: 2012.07.25 Increasing RUN LENGTH 3.00 2.00 n a2 d3 d4 PPU 1.76 2.00 N/A 3.00 .01 .01 .01 1.00 AJ05 .00 -.02 -.03 -.01 .00 AS05 .00 AA3=1 if bilateral PART Part number: A877 Part description 凸轮轴正时链轮 HOW MANY RUNS 3.00 7.00 2.00 1.88 .00 3.27 PPL 1.49 3.00 N/A 3.00 .02 .01 .02 1.00 AJ06 .00 -7.00E-03 -.01 .00 .00 AS06 .00 AA3=2 if Min Drawing number A877 Eng. chg. level B Decreasing RUN LENGTH 2.00 2.00 3.00 1.02 .00 2.57 .02 .02 .02 19.00 AJ07 18.00 7.00E-03 .00 .01 1.00 AS07 1.00 AA3=3 if Max TOOL Tool number 专用检具（GP12-33） # Cavities HOW MANY RUNS 8.00 7.00 4.00 .73 .00 2.28 .02 .02 .03 19.00 AJ08 .00 .02 .01 .03 19.00 AS08 18.00 DIMENSION Description 跳动度 Units MM Out of control limits .00 .00 5.00 .58 .00 2.11 .03 .03 .03 81.00 AJ09 62.00 .04 .03 .04 124.00 AS09 105.00 SPEC .00 PLUS .07 MINUS .00 Consecutive data points above avg. 2.00 5.00 6.00 .48 .00 2.00 .03 .03 .03 81.00 AJ10 .00 .05 .04 .06 125.00 AS10 1.00 1.00 Lwr Spec Limit 2.00 MIN Lwr Spec Limit .00 1.00 2.00 1.00 NOMINAL NOMINAL .00 1.00 1.00 Upr Spec Limit 2.00 MAX Upr Spec Limit .07 1.00 3.00 Consecutive data