- 1、本文档共11页,可阅读全部内容。
- 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
《pcb making requirements.docx (Autosaved)》.pdf
MAKING OF A PCB ETCHED RECTANGULAR
MICROPATCH ANTENNA WITH INSET FEED
Requirements:
1. PCB design software (EAGLE layout editor 6.0.0)
2. Magazine paper/advertisement brochure (A4 size)
3. Laser printer
4. Single sided Copper clad laminate or also called Radio shack (FR4 laminate 1.6µm
thick):1X1 feet
5. Iron machine
6. Etching solution powder: Ferrous chloride: 75 gms
7. Kitchen scrub: sponge/metallic: 1 piece
8. Nail polish remover/Thinner: Around 50ml
9. Cotton or Ear buds sponge
10. Water:1 small bucket(about 5-10litre)
11. Medium size plastic tub for preparing etching solution.
12. Couple of wires with hard plastic insulation to hold the PCB while etching
13. Fewikwik:2 packets
14. SMA co-axial 3.5mm Female socket connector:1peice
15. Soldering Iron, flux, lead.
Drawing of RMPA with Inset Feed using EAGLE 6.0.0
Getting the software:
EAGLE is an acronym of Easily Applicable Graphical Layout Editor. This software can be
downloaded from the website under downloads tab by clicking
Download Eagle option.
Opening the Eagle:
After installing it in system click Start-All programs-Eagle Layout Editor 6.0.0-EAGLE
6.0.0
Creating a New file:
After opening the EAGLE, click FILE-NEW-BOARD
Drawing a Schematic of Patch:
After we design the patch dimensions by using Design formulas of patch antenna, convert the
dimension from mm to inches as the EAGLE allows you to draw schematics in inches.
Now click on DRAW -Rect, This allows you to draw Rectangles of desired dimensions.
We can draw the complete Rectangular Microstrip Patch antenna with inset feed by drawing it as
4 Rectangles in EAGLE.
So, we have to calculate the dimensions of each and then we go for drawing.
Co-ordinates of the Rectangle,
(LENGTH, BREADTH) we can draw with a minimum
incremental dimension of 0.05inch
Rectangle drawn
您可能关注的文档
- 《JT 296-1996 汽车客动站卫生标准》.pdf
- 《JT-T525-2016公路水泥混凝土纤维材料_聚丙烯纤维和聚丙烯腈纤维》.pdf
- 《JT525-2016公路水泥砼纤维规范》.pdf
- 《JTG_E51-2016公路工程无机结合料稳定材料试验规程(全)》.pdf
- 《JTT 198-1995 汽车技术等级评定标准》.pdf
- 《JTT 199-1995 汽车技术等级评定的检测方法》.pdf
- 《JTT 324-1997 汽车喷烤漆房通用技术条件》.pdf
- 《JTT 425-2016 汽车维修业质量检验人员技术水平要求》.pdf
- 《JTT 441-2016 港口货场用化纤涂塑苫布技术条件》.pdf
- 《JTT 511-2016 压缩天然气汽车维护、检测技术规范》.pdf
文档评论(0)