备件储存保养标准论述.docx

永锋集团有限公司 备件储存保养标准 PAGE \* Arabic \* MERGEFORMAT2 / NUMPAGES \* Arabic \* MERGEFORMAT25 永锋集团有限公司 备件储存保养标准 目 录 第一章 电动机储存及在线备用保养标准·····················4 一、储存环境要求········································4 二、储存要求············································4 三、储存及在线备用期间的保养要求：·······················5 附件一 大型电动机转子转动方法···························6 第二章 离心风机储存及在线备用保养标准···················8 一、储存环境要求········································8 二、储存要求············································8 三、储存及在线备用期间的保养要求：·······················8 附件二 离心风机叶轮转动方法····························9 第三章 减速机储存及在线备用保养标准····················11 一、储存环境要求·······································11 二、储存要求···········································11 三、在线储存或备用期间的保养要求：······················11 第四章 轴及齿轮储存保养标准····························13 一、储存环境要求·······································13 二、储存要求···········································13 三、储存期间的保养要求：································13 第五章 变频器储存及在线备用保养标准·····················14 一、储存环境要求········································14 二、储存要求············································14 三、储存及在线备用期间的保养要求：·······················14 第六章 电子类备件储存保养标准··························15一、储存环境要求·······································15 二、储存要求···········································15 三、储存期间的保养要求：································15 第七章 考核·············································15  第一章 电动机储存及在线备用 保养标准 一、储存环境要求： 1、不允许有白蚁、盐雾、腐蚀性气体、危险性气体及过多类尘。 2、环境相对湿度不大于70%，但对于TH型电动机相对湿度可不大于95%。 3、储存地点应该通风良好，但不允许室外储存。户外型（包括露天）也不例外。 二、库存储存要求： 1、电动机储存时，应拆箱清除尘污，并将轴伸、集电环、进出水法兰等露出之表面擦净，清除原来涂上的临时性涂料及表面潮气和可能存在的表面锈渍等。用清洗液将油渍擦干净，表面仍有锈渍时，则可用00号细砂布加油轻轻擦光，再用防锈油或临时性涂封材料将表面重新涂封。 2、储存时电机应进行全面密封处理，以防异物进入。 3、禁止将电动机与磁性件及具有化学腐蚀性酸、碱及蓄电池等物品存放在一起。 4、对绕线型电机，为了防止集电环的工作表面形成斑点，在集电环与电刷间应垫以绝缘板。 5、使用过的电动机，如停止使用并打算储存起来的话，必须将电动机全部拆开清理干净，电动机组装前，轴承清理注上新的润滑脂，对于水—空冷却型电动机，还必须将冷却器里面的水和污物清理干净，并将轴伸、集电环、进出水法兰等按1条的要求清理干净，滑动轴承必须将轴承里的润滑油放干净，轴颈和轴瓦用油脂涂封，以免锈蚀。 6、经过检查和清理的电动机，必须放入包装箱内进行储存，无包装箱的应进行包裹或遮盖。装箱的地点应该清洁，无过多灰尘、无盐雾、无腐蚀性和危险性气体。检查和清理