(加工中心报警信息表.docVIP

EX0013 主轴或旋转刀具主轴接通 PER0013 在主轴或旋转刀具主轴旋转期间，就已经发出了一个自动门打开指令。 EX0018 所有的轴都需要回零 PER0018 在机床锁紧取消之后，没有进行所有轴的回零，就起动了一个循环开始。 EX0019 工件计数器处于满数 PER0019 PC或外部工件计数器已经数满时，还是起动了一个循环开始。 EX0020 编辑键开关接通 PER0020 编辑键开关接通着，就已经起动了循环开始。 EX0021 TOOL IS NOT CLAMPED PER0021 A cycle start has been activated with the tool is not clamped. EX0023 起动互锁信号接通 PER0023 当已经输入了一个外部开始互锁信号时，已经起动了一个循环开始。 EX0024 卡盘没有夹紧 PER0024 卡盘没有夹紧，就起动了循环开始。 EX0026 请关门 PER0026 没有关门，就起动了循环开始。关门。 EX0029 尾座活动套筒没有伸出 PER0029 在尾座缓动期间或尾座主轴没有OUT（伸出）时，就已经起动了一个循环开始。 EX0035 切断不完全 PER0035 切断还没有完成。 EX0068 互锁释放超时 MER0068 门互锁取消状态已经失效。 EX0069 门互锁超时 MER0069 在定时器中所设定的经过时间之后，就已经接通了门锁紧完成信号。 EX0097 面板I/O报警 MER0097 在平板式操作面板中已经发生了I/O报警。 EX0099 面板报警 MER0099 在平板式操作面板中已经发生了报警。 EX0103 INTERLOCK BYPASS ON PER0103 ATC-command has been given while interlock bypass is on. EX0116 REFERENCE POINT PARAMETER ERROR PER0116 X-or Y-or Z-axis 3rd zero-point has not been properly set at parameter. EX0123 NO EMPTY POT IS EXISTING PER0123 No empty pot exists during ATC cycle. Check the tool data. EX0124 SPECIFIED POT IS NOT INDEXED PER0124 The pot specified by T-code has not been indexed at change position during ATC cycle. EX0126 EMPTY POT IS EXISTING PER0126 An empty pot exists even if the spindle tool data is 0. Check the setting of tool data again. EX0134 X,Y-AXIS NOT IN ZERO POINT PER0134 ATC-command has been geven with X, Y-axis is not in zero point. EX0135 NO EMPTY POT IS EXISTING PER0135 An empty pot does not exist even if the spindle tool data is not 0. Check the setting data again. EX0139 ATC CANNOT POERATE WITHOUT TOOL IN SPINDLE OR STANDBY PER0139 The ATC command is specfied in states that the tool is not at the spindle or the standby position. EX0147 ATC DATA ERROR PER0147 G361(ATC) was commanded without dammy holder./T** was commanded without LBB-MG home position./G361(LBB) was commanded without special tool(LBB adapter tool)/B-axis commanded with LBB holder. EX0155 ATC HOME POSITION SIGNAL OFF PER0155 ATC home posotion has