可行性模版解读.ppt

Page Page HAN * Project name:SGM358 Issue: DFM – Design For Manufacture - dated the 2015.09.07 上海瀚氏模具成型有限公司 HANSI Engineering DFM-REPORT. Shanghai HANSHI Molding Shape CO.,LTD 产品信息 Product Information mould No: HAN2441 Customer Name: 内侧旁侧板-驾驶座(乘客座），CT/LT INR SIDE SHIELD-DRV,CT/LT Customer mould No.: 2779649/2779654 Drawing No.: Cavities: *CAV Material: PP+EPDM+M20 Part weight: 440g/440g Part size: 591 X 79 X 280 Inch/mm: MM * Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 上下模分析 CAV/COR * CAV COR Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 进浇口建议 Gate Advice * 扇形胶口,胶口尺寸20mm*1mm Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 结构分析 Structure analysis * 箭头方向为斜顶退出方向 斜顶1 斜顶2 斜顶4 斜顶3 斜顶5 斜顶6 斜顶7 * 结构分析 Structure analysis 图中绿色的面脱模斜度为0度，请确认的面是否需要做皮纹，如果要做皮纹脱模角度需做到8度， 如果不是皮纹面，脱模斜度也必威体育精装版少需1度 脱模角度不够 YF回复：此区域不拔模2015-8-26 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG * 结构分析 Structure analysis 脱模角度不够 红色的框内绿色的面为皮纹区域 脱模斜度需做到8度，现在角度小于8度，请加到8度以上 YF回复：做皮纹时处理。2015-8-26 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 产品分析 Product analysis * 脱模角度不够 YF回复：瀚氏拔模。2015-8-26 图中绿色的筋条面没有脱模角度，产品不易脱模，建议减胶拔模筋位口部0.7mm根部0.9mm。 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 产品分析 Product analysis * 图中红色的面按斜顶退出方向没有脱模角度，斜顶退出时会拉伤产品，需做1度的脱模角度（红色的箭头方向为斜顶的退出方向） 脱模角度不够 YF回复：瀚氏拔模。2015-8-26 此处已按照新数据处理。详见3D Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 产品分析 Product analysis 图中绿色的面按斜顶退出方向没有脱模角度，1：斜顶退出时会拉伤产品:2:斜顶退出时产品容易跟着斜顶走。需做1度的脱模角度 脱模角度不够 箭头方向为斜顶的退出方向、 YF回复：瀚氏拔模。2015-8-26 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 产品分析 Product analysis * 图中绿色的面按斜顶退出方向没有脱模角度，1：斜顶退出时会拉伤产品:2:斜顶退出时产品容易跟着斜顶走。需做1度的脱模角度