- 1、本文档共3页,可阅读全部内容。
- 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
ledtaillights
INSTALLATION INSTRUCTIONS
LED TAILLIGHTS FLASHERS INSTALLATION
41-04-010 4” Red 6-LED Flange Mount
41-04-050 4” Red 24-LED Push-In
41-04-051 4” Clear 24-LED Push-In
41-04-026
41-04-106
41-04-262
4-Pin LED Flasher 97-2000 TJ 5-Pin LED Flasher 01-06 TJ/LJ 2-Pin LED Flasher 76-95 CJ/YJ
LED TAIL LIGHT INSTALLATION Poison Spyder Customs 4” LED taillights are designed to work with Poison Spyder Crusher Corners that were specifically made for aftermarket LED taillights. They also work with other manufacturer’s corner protectors, or on Jeeps without any corner protectors. In all cases, a 4-1/2” round hole must be cut into corner protector or sheet metal to install the LED (plus screw holes for the flange-mount style LED). These instructions do not cover the procedure for creating this mounting hole, it is assumed that it is already present or you purchased Poison Spyder Crusher Corners already made for LED taillights.
1. Pull the factory wiring harness taillight plug through the 4” LED hole to have room to work.
2. Cut the factory taillight plug from the stock taillight pigtail (between the plug and the taillight). You will re-use the taillight side of this plug. Leave as much wire as possible.
3. Use the information in Table 1 to make the correct connections between the cut wires from the factory taillight plug, and the
black and red wires in the supplied LED pigtail harness. Whether you solder or crimp-connect, we recommend using heatshrink tubing on all connections. Once the necessary electrical connections have been made, plug the OEM pigtail plug (now with the LED pigtail attached) back into plug in the Jeep’s chassis harness. Do not plug the opposite end of the pigtail into the LED lamp fixture at this time.
4. Tape-off unused wires in the stock harness. These will be the violet/black wire on both sides (unless you are wiring your own, separate back-up lights) and the green/red wire on the passenger side, which is unused. Stow these wires inside the wire loom or
您可能关注的文档
- DimmableCFL&LEDbulbs-LutronElectronics.pdf
- DMS-11011LEDROADWAYLUMINAIRES-Welcometo.pdf
- DSSSERIES-LED-USPoleCompany,Inc.pdf
- DevelopingaFacultyLedStudyAbroadProgram.ppt
- EasilyupgradetoLEDfromfluorescent.-Philips.pdf
- ELite-LED.pdf
- ELECTROMECHANICALCONTROLLERS-RainBird.doc
- DSAPSERIES-LED-USPoleCompanyInc.pdf
- DIYLEDVideoCube-cdn.pdf
- EmersonClimate.com.pdf
文档评论(0)