- 1、本文档共34页,可阅读全部内容。
- 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
毕业论文(设计)
题目:车床Z向进给数控改造
校区(函授站):
专 业
班 级
学 号:
学生姓名:
导师姓名:
起止时间:
毕业论文(设计)任务书
学生姓名 指导教师 职称
校区(函授站) 专业 机电一体化
题目 车床Z向进给数控改造
任务与要求
1.完成一台机床工作台的数控改造;要求工作台能实现点位(或连续)控制;
2.改造部分进给伺服系统一个坐标轴的机械装配图一张(A1);
3.计算机I/O接口、驱动电路等电路原理设计图一张(A1);
4.设计说明书8000字左右(前言,控制系统总体方案的分析及框图,机械部分设计计算,机构设计说明,硬件电路设计说明,技术经济分析,结束语,参考文献,后记,附录);
5. 选步进电机为驱动电机,脉冲当量取0.01mm/step;
6. 旋转——移动的转换用滚动丝杠;
7. 能用键盘输入命令,控制工作台;能实时显示工作台当前运动位置;有超越边界报警,并停止运动。
原始数据:
1. 工作台(或刀架)重G=180N;
2.工作台行程L=0~300mm;
3.工作台最大移动速度Vmax=3m/min;
工作台工作进给速度Vmax=1m/min;
4.切削分力:FX=420 N,FY= 1100N,FZ=1660 N;
5.工作台尺寸:300×550mm2;
6.各传动部件的设计寿命15000~48000h。
开始日期 完成日期
目录
概述···············································································1
总体设计方案的拟订··················································5
总体方案确定································································5
经济型数控车床总体方案框图··················································6
车床进给伺服系统机械部分设计计算······························7
选择脉冲当量·······························································7
计算切削力·································································7
滚珠丝杠螺母副的计算和选型·················································7
2.3.1 计算进给牵引力Fm··························································7
2.3.2 计算最大动负载C···························································7
2.3.3 滚珠丝杠螺母副的选型·······················································8
2.3.4 传动效率计算·······························································8
2.3.5 刚度验算···································································8
2.3.6 稳定性校核·································································9
2.3.7 滚珠丝杠副几何参数·························································9
2.4 齿轮传动比计算······························································10
2.5 步进电机的计算和选型························································10
2.5.1 初选步进电机··························································
文档评论(0)