鞋成型工艺说明解决方案.ppt

鞋面與大底成型ASSEMBLE UPPERO/S 1. 浸 康 特SOAK TR COUNTER 30.清潔大底烘線 CLEAN O/S HOT THREAD EDGE 1,用633BF+水把大底清洗干淨. Clean O/S with 633BF+ water. 2.烘外露的線頭. Hot the exposed thread edge. 清洗大底 烘線頭 1,核對成品鞋的SIZE. Check the finished size. 2.3,准備相應SIZE內盒,并貼上相應的內盒標,需貼在規定的位置. Prepare the shoe box plate of corresponding size to fold. Then attach the corresponding shoe box label on the indicated position. 4. 將鞋子用包裝紙包好,再裝入內盒. Pack the shoe with wrapping paper then put into the corresponding shoe box. 31.折內盒包裝 FOLD SHOE BOX PACK 2.折內盒 3.貼內盒標,SIZE要與成品鞋一致 1.核對成品鞋SIZE 4.將成品鞋包入內盒 * * 依照鞋子結構的不同, 通常分車中底與結幫兩種成型流程:According to the different shoe construction, there are two kinds of assembly procedure ,strobel lasting.結幫流程又分為一次流程及兩次流程或多次流程.For the lasting construction, there are 3kinds of procedure ,one time lasting two times lasting or more than two time lasting.這裡僅以一次結幫流程為例,了解成型的過程:Here only show the one time lasting procedure for example to know the assembly procedure: 1,浸康特時注意康特角不要浸膠。 Pay more attention to the bottom of TR counter can’t be soaked. 2﹐用鑷子夾住康特放入513藥水中,只要除康特腳外其他部分有碰到膠水,就馬上取出來.浸膠不宜過久﹐過久會使康特軟化。 Clip the counter with forceps and then put it into 513 primer . Don’t soak counter too long to avoid the counter from soften. 3﹐康特浸好后需放在鐵綱滴干。 Put the counter on the iron shelf after soaking. 4﹐康特擺放鐵架上涼干時不宜過久,不要超過15分鐘。 Make the counter dry not more than 15 minutes. 5.操作員應戴上手套及口罩等環保用品. The operator should wear the safe things of glove respirator. Applied Tooling: 鐵網 Iron meshwork 手套 Glove 鑷子 forceps 鐵架 Iron shelf 1,從裝鞋面的車架上取下鞋面,貼上流水標以便配雙作業,剪斷連線,放鞋面入流水帶上. Take the upper from the shelf and attach pair number sticker, then snip the thread that make one pair of upper together, at last put upper on conveyer belt. 2,剪線時不要剪到鞋面.Don’t break the upper when snip thread.3.注意鞋面要配雙. Note: Need make the upper pair. 2.准備放鞋面PREPARE UPPER Applied Tooling: 剪刀 scissor 1.取一小塊泡棉,對折好再夾在夾子上,刷膠時將泡棉在膠水裡浸一下. Prepare a little piece of foam or cloth and fold then nip it with clamp. Soak a momen