《单机互动型汽车模拟驾驶培训系统安装及使用指导》.doc

《安装及使用指导》 第  PAGE 28 页 共 27 页 单机互动型汽车模拟驾驶培训系统2.0 《安装及使用指导》 三联（上海）集团 2005年8月 Ⅰ.产品介绍·······················································3 Ⅱ.搬运操作指导···················································3 Ⅲ. 安装指导······················································4 一、设备的安装指导································································4 安装现场的要求···························································4 单座舱的安装·····························································4 二、软件的安装指导·······························································5 单机互动型汽车模拟驾驶培训系统软件的安装····························5 操作系统的设置··························································9 Ⅳ.使用操作指导··················································17 一、操纵装置的介绍······························································17 二、操纵装置的检测······························································19 三、小键盘的使用介绍····························································20 四、软件的使用介绍·······························································20 1、主界面的使用······························································20 2、教学片的使用······························································20 3、训练场景的使用·····························································21 Ⅴ. 注意事项·····················································26 产品介绍 单机互动型汽车模拟驾驶器是三联（上海）集团研制的高科技产品，具有实车仿真、实时纠错、主被合一、方便升级等特点，是汽车驾驶理论学习和操作训练的一种现代化教学设备。单机互动型汽车模拟驾驶器由豪华玻璃钢、座舱支架、计算机和电子电路等部分组成，采用桑塔纳实车配件（包括座椅、仪表、方向盘和方向盘总成等），进一步仿真实车驾驶环境，提高训练效果。 座舱示意图 （图1） 搬运操作指导: 设备的搬运应在我公司的工程人员指导下进行，如客户要自行搬运设备应注意以下几点： 要装车运输时，以下部件需要用出厂原包装箱打包运输，不能连接在设备上运输： 计算机主机 显示器 座舱搬运前需打开后盖板，并把后盖板固定螺丝拧回机架上的安装孔上，并作如下检查： a) 检查计算机主机、显示器是否拆除。 b) 检查座舱内部连线捆扎是否整齐(或作临时捆扎)，没有线垂地，没有线过长悬垂(悬垂部分长度小于20cm)，没有线悬垂在方向机构的弹簧附近或被弹簧夹住。 c) 检查除后盖板外其余结构部分是否连接紧固。 d) 检查是否没有电源连接。 座舱人工搬运过程中的着力点为座椅下方的座椅安装座、安装后盖板处的上下两根角钢，严禁在其它处用力(如：安全带、方向机构、玻璃钢部分、手刹车等)。 4、座舱人工搬运过程中如果有