模具工程常用词汇模具工常用词汇.doc

模具工程常用词汇 * 注：链接到相关页后请按Ctrl+f可以快速有哪些信誉好的足球投注网站 组装、冲压、喷漆等专业词汇 瑕疵常用词汇defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 aberration 色差 atomization 霚化 bank mark 滞料纹 bite 咬入 blacking hole 涂料孔(铸疵) blacking scab 涂料疤 blister 起泡blooming 起霜 blow hole 破孔 blushing 泛白 body wrinkle 侧壁皱纹 breaking-in 冒口带肉 bubble 膜泡 burn mark 糊斑 burr 毛边 camber 翘曲 cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂 chipping 修整表面缺陷 clamp-off 铸件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蚀 crack 裂痕 crazing 碎裂crazing 龟裂 deformation 变形 edge 切边碎片 edge crack 裂边 fading 退色 filler speak 填充料斑 fissure 裂纹 flange wrinkle 凸缘起皱 flaw 刮伤 flow mark 流痕 galling 毛边 glazing 光滑 gloss 光泽 grease pits 污斑 grinding defect 磨痕 haircrack 发裂 haze 雾度 incrustation 水锈 indentation 压痕 internal porosity 内部气孔 mismatch 偏模 mottle 斑点 necking 缩颈 nick 割痕 orange peel 橘皮状表面缺陷 overflow 溢流 peeling 剥离 pit 坑 pitting corrosion 点状腐蚀 plate mark 模板印痕 pock 麻点 pock mark 痘斑 resin streak 树脂流纹 resin wear 树脂脱落 riding 凹陷 sagging 松垂 saponification 皂化 scar 疤痕 scrap 废料 scrap jam 废料阻塞 scratch 刮伤/划痕 scuffing 深冲表面划伤 seam 裂痕 shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折迭 straightening 矫直 streak 条状痕 surface check 表面裂痕 surface roughening 橘皮状表皮皱折 surging 波动 sweat out 冒汗 torsion 扭曲 warpage 翘曲 waviness 波痕 webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皱纹missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属) flash(塑件)毛边 poor staking铆合不良excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-