- 1、本文档共10页,可阅读全部内容。
- 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
PAGE 1
PAGE 10
.
Die Construction Guidelines
Press Parameters 压床要求
Dies will have ‘U’ clamping slots to suit press slots and clamping flange thickness should be 55 mm. Mahindra and Mahindra will be using either Bolt clamping method or hydraulic die clamps.
模具上应布置与机床压板槽位置相对应的‘U’型槽,厚度为55mm。马恒达公司装卡模具采用手动装卡和气缸装卡两种方式。
One rectangular and one ‘V’ slots, for anchoring shall be provided on the rear end of bottom shoe of the die. Locating pins will be of 50-mm diameter.
下模本体出料方向设置左平右槽的模具快速定位。定位销的直径为Φ50mm。
Proper care will be taken at the die design stage to ensure, ease of part loading and unloading.
模具设计时要注意确保制件取送的方便。
Multi loading provision to be considered, wherever possible.
如果可能,可以采用多槽模。
Draw dies will be single action types.
拉延模具采用单动。
Long dies are to be designed, such that it is possible to load them front to back rather than right to left.
多槽模设计时,送件的方向优选从前到后,其次为从右到左。
Die and Tool Parameters 模具要求
Material Specification Of Dies 模具材质要求
Type Of DieMaterialDraw Dies拉延模具
Die / Punch / Blank Holder凹模/凸模/压边圈
CrMo / GM 241Trim Dies修边模具
Punch and Di e修边镶块
Top , Bottom Castings and Stripper 上下模本体和压料芯
M16 / ICD5 / SKD11
GG-25 / FC-30Restrike / Flanging Burring Form Dies
整型/翻边和翻孔和成型模具
Punch凸模
Die 凹模
Pad压料芯
CrMo / GM241 / SKD11
OHNS / SKD-11 or ICD5
GG-25 / FC-30CAM Tools 斜楔模具
Bottom Top Shoe, Stripper 上下模本体和压料芯
CAM Driver / CAM Slider斜楔驱动器和滑块
Wear Plate导板
GG-25 / FC-30
GG-25 / FC-30
Oil-less
Basic Die Construction 基本的模具结构要求
Draw Dies 拉延模具
Top and bottom shoes should be guided with heelpost.
上下模之间采用导腿导向。
Blank holders to be guided on the punch using oil-less wear plates.
压边圈与凸模之间的导板采用自润导板。
All working radii should be duly flame hardened.
所有的工作圆角都应进行适当的火焰淬火处理。
Provide hardened plate below bottom face of pad to avoid diggi
文档评论(0)