如何用英文和老外检讨模具教程.doc

如何用英文和老外检讨模具 1. 请问此产品的表面是否为外观面？表面做什么处理？是晒纹/抛光？ CAN YOU TELL ME WHETHER THE SURFACE OF THIS PART IS A VISIBLE/ESTHETIC ONE？ WHAT WILL WE DO FOR ITS SURFACE？ TEXTURE OR POLISHING？ 2. 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？ THERE‘S AN UNDERCUT AT THIS POSITION AND IT NEEDS A SLIDER。IT WILL ALSO HAVE A PARTING LINE ON THIS SIDE, IS THAT OK? 3.产品里面的这个位置我们打算做斜顶或内行位,有问题吗? WE WILL MAKE THE LIFTER AND INNER SLIDER IN THIS POSITION. WILL THAT BE A PROBLEM? 4.你提供的3D产品图有的地方没有出棱角,有的地方胶位太厚,有的地方胶位太薄,这些产品问题我们可以修改吗?修改后给你们确认. THERE IS NO DRAFT ANGLE IN THE 3D DRAWING, SOME MATERIALS ARE TOO THICK, AND SOME MATERIALS ARE TOO THIN. CAN WE MODIFY THIS PART BY OURSELVES? WE WILL SENT THE DRAWING TO YOU AFTER WE MODIFY IT. 5.你们提供的2D产品图和3D产品图不一致,请问以哪一个图面为准? THE 2D AND 3D DRAWING YOU PROVIDED IS NOT THE SAME, CAN YOU TELL ME WHICH ONE IS CORRECT? 6.按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面的要求.但注塑出来的产品不符合你们的产品图.请确认你们的材料的缩水率是否正确? ACCORDING TO THE SHRINKAGE ONE OVER TWO HUNDRED, THE MOLD HAS BEEN DONE IN THE RIGHT DIMENSION. BUT THE PART FALLS SHORT TO YOUR PART DRAWING, ARE YOU SURE THE SHRINKAGE IS RIGHT? 7.这个胶骨位胶太厚,而且高度偏高,注塑时很难填充这个筋位,可以增加这个筋骨位的厚度吗? THE RIB HERE IS TOO THIN AND ON THE HIGH SIDE, SO IT WILL BE DIFFICULT TO FILL HERE WHEN WE DO THE INJECTION, CAN YOU INCREASE THE THICKNESS OF THIS RIB? 8.产品的这个面我们已经做好晒纹处理如果需要加胶,这个面我们需要重新外发晒纹.可能需要几天时间.所以我们直接以铜公放电的火花纹取代你要求的花纹,你可以接受吗? WE HAVE MADE THE TEXTURE ON THIS SIDE, IF WE ADD MATERIAL, IT WILL TAKE SOME DAYS TO REMAKE THE TEXTURE BY OUT-RESOURCING, SO WE SUGGEST USING THE TEXTURE BY EDM INSTEAD, IS THAT OK? 9.此面不是外观面,此处做滑快的话会有夹线,是否可以接受? PLEASE CONFIRM WHETHER IT IS A CRITICAL SURFACE OR NOT. ALSO, CONFIRM WHETHER IT IS ACCEPTABLE TO HAVE A SLIDE SPLIT LINE IF WE HAVE A SLIDE IN THIS AREA. 10.你是想将此筋骨位的高度加高或减低吗?加胶的位置我们将用铜公放电加深.但减胶的位置有两种做法,1. 做镶件;2,烧焊;因为镶件的底步有运水,我们简单的做法是烧焊处理,你可以接受吗? WILL YOU INCREASE OR DECREASE THE MATERIAL ON THIS RIB? WE WILL USE EDM IF YOU ADD MATERIAL, BUT THERE ARE TWO OPTIONS IF YOU CHOOSE TO DECREASE:1. MAKE INS