砂轮机安全操作规程（五）.doc

砂轮机安全操作规程（五） 砂轮机安全操作规程（五）提要：工件的托架必须安装牢固，托架面要平整，托架的位置与砂轮架的间障不得大于3mm，夹持砂轮的法 源自建筑资料 砂轮机安全操作规程（五） 一、砂轮机应安装在僻静安全的地方，旋转方向禁止对着通道，启动前，应先检查机械各部螺丝、砂轮夹板、砂轮防护罩、砂轮表面有无裂纹破损等，确认完整良好再启动。 二、工件的托架必须安装牢固，托架面要平整，托架的位置与砂轮架的间障不得大于3mm，夹持砂轮的法兰盘直径不得小于砂轮直径的三分之一，夹合力适中。对有平衡块的法兰盘，应装好砂轮后，先进行平衡测试，合格后方能使用。 三、砂轮要保持干燥，防止受潮而降低强度。 四、砂轮轴关紧固螺丝的转向，应与主轴旋转方向相反，以保持紧固。砂轮起动须达到正常转速后，方准进行磨件。 五、严禁两人同是使用一个砂轮打磨工件。 六、砂轮不圆、厚度不够或者砂轮露出中易发生震动的工件。 七、磨工件时，不准震动砂轮或打磨露出中易发生震动的工件。 八、砂轮只准磨钢、铁等黑色金属，不准磨软质有色金属或非金属。 九、砂轮禁装倒顺开关，中途停电时，应立即切断电源。 十、磨工件时，应使工件缓慢接近砂轮，不准用力过猛或冲击，更不准用身体顶着工件在砂轮下面或侧面磨件。 十一、磨小工件时，不应直接用手持工件打磨，应选用合适的夹具夹具夹稳工件进行操作。 十二、安装砂轮片时，不准用铁锤进行敲击。如孔大于轴径，应加套筒不得有空隙，轴端须有两个以上的螺母紧固。根据旋转方向来用正、反旋螺纹。 十三、砂轮机转轴发生弯曲后，应立即停用，更换新部件后方可继续使用。 源自建筑资料 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image qualit