学校办公楼起重吊装作业方案.doc

学校办公楼起重吊装作业方案 学校办公楼起重吊装作业方案提要：检查电源电压应达到380V，其变动范围不得超过±20V，送电前启动控制开关应在零位。接通电源，检查金属结构部分无漏电后方可上机 自 学校办公楼起重吊装作业方案 本工程采用QTZ40塔式起重机各一台，用于吊装砖、模板、钢筋、砼等。施工时要严格按施工现场平面布置图的要求堆放材料。 1、塔吊施工前应重点检查下列内容： （1）机械结构的外观情况，各传动机构应正常； （2）各齿轮箱、液压油箱的油位应符合标准； （3）主要部位连接螺栓应无松动； （4）钢丝绳磨损情况及穿绕滑轮应符合规定； （5）供电电缆无破损。 2、检查电源电压应达到380V，其变动范围不得超过±20V，送电前启动控制开关应在零位。接通电源，检查金属结构部分无漏电后方可上机。 3、空载运转，检查行走、回转、起重、变幅等各机构的制器、安全限位、防护装置等确认正常后，方可作业。 4、操纵各控制器时应依次逐级操作，严禁越档操作。在变换运转方向时，应将控制器转到零位，待电动机停止转动后，再转向另一方向。操作时力求平稳。严禁急开急停。 5、吊钩提升接近臂杆顶部、小车行至端点时，应减速缓行至停止位置。吊钩距臂杆顶部不得小于1米。 6、提升重物后严禁自由下降。重物就位时可用微动机构或使用制动器使之缓慢下降。 7、提升的重物平移时应高出其跨移的障碍物米以上。 8、作业后吊臂应转到顺风方向，并放松回转制动器。小车应移至非工作状态位置。吊钩提升到离臂杆顶端2-3米处。 9、将每个控制开关拨至零位，依次断开各路开关，关闭操作室门窗，下机后切断电源总开关。打开高空指灯。 10、任何人员上塔帽、吊臂、平衡臂的高空部位检查或修理时，必须佩带安全带。 自 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX studen