【2017年整理】家电外饰件表面检验要求.doc

注塑外饰件表面控制要求Injection control requirements for exterior surface 外观 Appearance 具体见附表 See the attached table of detailed defects. 色差控制 Color control 制件表面色差控制：颜色按封样色板，Δ≤0.7（D65光源）。 Color control: the color refer to standard sample Δ≤0.7（D65 light source）Painting control 制件喷涂：a.喷涂均匀完整、不粗糙、无暗纹、亮斑，不能有局部堆积，少油、纤维丝；b.喷涂牢固，硬度符合要求。喷涂层色差光泽均匀、光亮；c.附着力用百格刀划格，用胶带迅速拉，不露底为合格 Components painting:: a. painting complete, not rough, no dark grain, and light spot, cannot have the partial stack, few oils, and fiber. b. painting is reliable, degree of hardness meets the requirement. The painting is luminous; c. pulls rapidly with the adhesive tape, doesn’t reveal the inside story is qualified. 丝印控制 Silk-screen control 制件丝印：a.图标、字符位置、尺寸按图纸要求或与封样件对比，颜色按PANTONE色卡检验；b.印刷文字应清晰，无明显锯齿及断线、气泡、扭曲等缺陷；c.附着力要求：依据GB／T9286测试，或用3M 600＃测试胶带贴于丝印部位，压实并挤出气体，迅速拉起，丝印应无粘脱、损伤现象，同一位置测试2次；d.抗酒精溶剂性：用白色棉布蘸酒精在丝印表面反复擦拭10次（不用大力按压），棉布上应无丝印油墨，丝印面无损伤、模糊现象。 Components print screen: a. icon, the place of the character, size should be made as the drawing, and check the color according to the PANTONE card. Printing should be clear and no obvious defects like saw blade, bubble, distortion: c: requirement for the adhesion : test according to the GB T9286, or place the adhesive tape on the silk screen , then pulls the adhesive tape quickly, the silk screen should be complete , make the test on the same place for twice. d;. anti- alcohol : Dips the ethyl alcohol with the white cotton fabric to clean 10 times repeatedly in the silk surface(don’t press it with too much power.) The silk screen should be complete and clear. 附表 Attached table of detailed defects (Q/BQJ07-04-004-2008): 外观缺陷 Appearance defect 面积限度（平方毫米） Limit of square (mm2 ) ≤400 400~2500 ＞2500 A B C A B C A B C 划痕、擦伤 Scratch L≤2 W≤0.1 Q≤1 L≤5 W≤0.1 Q≤1 L≤5 W≤0.2 Q≤1 L≤2 W≤0.1 Q≤1 L≤5 W≤0.1 Q≤2 DS≥50 L≤5 W≤0.2 Q≤2 DS≥50 L≤2 W≤0.1 Q≤3 DS≥100 L≤5 W≤0.1 Q≤3 DS≥100 L≤5 W≤0.2 Q≤5 DS≥50 磕碰、压痕 Indent L≤1 W≤0.1 Q≤1 L≤5 W≤0.1 Q≤1 L≤5 W≤0.2 Q≤1 L≤2 W≤0.1 Q≤1 L≤5 W≤0.1