东北家常菜地三鲜的简易做法(图文).doc

  1. 1、本文档共5页,可阅读全部内容。
  2. 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
东北家常菜地三鲜的简易做法(图文)

东北家常菜-地三鲜的简易做法(图文)   地三鲜的做法收集整理于网络,菜谱所属菜系为东北家常菜,地三鲜菜谱的做法非常简单,根据以下图文提示,您一定可以做出美味可口的菜肴,如果本菜谱步骤有误或不符合实际,请留言提出,我们会及时更改。   东北家常菜-地三鲜的做法介绍   前面介绍了地三鲜的做法,这次发布一个图解地三鲜做法菜谱,让大家能够把这道美味的菜做的更好!   地三鲜的做法是这样的:   1、把三样材料(土豆、茄子、青椒)大切八块,切片切条都可以,但是千万别太小、太秀气了,好歹这也是个东北菜啊。      2、铁锅里放大量的油。油多也是东北菜的一大特点。放入土豆狂炸,就像麦当劳的炸薯条一样。炸三分钟。捞出。      3、剩下的油炸用来炸茄子,炸2分钟,捞出。   4、剩下的油炸用来炸青椒,放下去马上捞出      5、把锅里的油倒掉一点。(否则就要发胖、得病了)放入葱花、蒜丁,爆香。倒入水淀粉,搅和。马上放入三种炒过的蔬菜,倒入酱油、黄酒、盐、鸡精、一勺排骨汤(当时同时在做萝卜排骨汤),翻炒,装盘。    Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of the pipe wall thinning rate must not exceed the original 15%. Crease roughness: diameter 125 mm or less, shall not exceed 3 mm diameter less than or equal to 200 mm, not more than 4 mm. 7.3.9 simmering bending production of square steel tube extension, to use the whole tube bending. Interface if necessary, the welding position should be located in the middle of the vertical arm. 7.3.10 install expansion joints should be done. If design is not required, pipe compensator lengthen should conform to the requirements in the following table: square scale length δ x is equal to 1/2. Pre stretch tolerance: casing + 5 mm, +10 mm. 7.3.11 pipe form, location, spacing shall meet the design and specifications. 7.3.12 piping on back or return pipe at higher levels of the upper to automatic valve to install a drain valve below the horizontal parts. 7.3.13 supports and hangers of checks and the number 1) hanger installed must be checked before installation of supports and hangers part models, specifications of springs setting values, whether the materials meet the requirements of drawings and documents; 2) supports and hangers of material, size and accuracy shall conform to the provisions of the design drawings, material technical requirements should be consistent with national standards, industry standards and technical requirements relat

您可能关注的文档

文档评论(0)

1444168621 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档