上海永大日立电梯按键的使用方法（The use of the key of Shanghai yongda Hitachi elevator）.doc

下载文档 降价啦

17
0
约1.14万字
约 16页
2017-07-15 发布于河南
举报
版权申诉
保障服务

上海永大日立电梯按键的使用方法（The use of the key of Shanghai yongda Hitachi elevator）.doc

1、本文档共16页，可阅读全部内容。
2、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

上海永大日立电梯按键的使用方法（The use of the key of Shanghai yongda Hitachi elevator）

上海永大日立电梯按键的使用方法（The use of the key of Shanghai yongda Hitachi elevator） mode-0-set Function: return to normal display Usage: no matter once MODE enters any module, will automatically reset, reply to floor display status Reset: far down the ESET Mode-1 - SET Function: elevator running time display Usage: show the time of the elevator running in decimal system. If it shows 000123, it will run 123 hours This pattern is purely for observation, if you want to change the reference MODE -24-set RESET: mode-1 - RESET Mode-2 - SET Function: monitor fault data read and all cleared 1. Press the INC button to read the fault data from 01 to 74 and press the RESET button until normal Display only, the failure record is cleared 2. According to MODE - 10 - SET, press MODE - 2 - SET, and the fault information will automatically be displayed by 01 The display was 74, but the display was long. (each number is about 3 seconds) Before cleaning up the failure record, record data from 01 to 74 as a reference. Some failure records are not Can be removed directly (after handling the cause of failure), switch power switch once, and MODE - 2 - SET clear In addition to RESET: RESET mode-3-set Function: the machine room controls the elevator running at low speed Use: 1. The box must be normal and fast, and has been closed inside and outside the door 2. Press the 7 button to control the elevator to rise slowly, according to the four-word button to control the elevator to slow down RESET: MODE - 3 - RESET mode-4-set Function: record of the minimum layer box button Use: 1. Make the elevator to the lowest level as normal and fast 2. When maintenance status, the elevator will slow down automatically (reference mode-21-set) RESET: automatic RESET Mode-5 - SET Function: middle layer machine button record Usage: when normal speed, make the elevator to the middle floor RESET: automatic RESET MODE -7 - SET Function: record of the top box button Use: 1. Make the elevator to the highest level as normal and