在写刀路之前,将立体图画好后,要将图形中心移到坐标原点,最高点移到Z=0,方可以加工,铜公火花位可加工（Before writing the knife path, after the stereo picture is good, the center of the picture is shifted to the coordinate origin, the highest point is moved.docVIP

下载本文档

8
0
约1.49万字
约 11页
2017-07-24 发布于河南
举报
版权申诉

在写刀路之前,将立体图画好后,要将图形中心移到坐标原点,最高点移到Z=0,方可以加工,铜公火花位可加工（Before writing the knife path, after the stereo picture is good, the center of the picture is shifted to the coordinate origin, the highest point is moved.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

在写刀路之前,将立体图画好后,要将图形中心移到坐标原点,最高点移到Z=0,方可以加工,铜公火花位可加工（Before writing the knife path, after the stereo picture is good, the center of the picture is shifted to the coordinate origin, the highest point is moved Before writing the knife path, after the stereo drawing is finished, the center of the picture is shifted to the coordinate origin, and the highest point is moved to Z=0, so that the copper can be processed, and the copper spark position can be processed with negative reserve. Before processing, it is necessary to check whether the clamping direction of the workpiece is the same as that in the computer, whether the position is correct in the mold, whether the fixture is blocked, and whether the direction of the front die and the die match. Also check whether the tools you use are complete, the standard in the meter, and so on. Matters needing attention in processing copper: Determine the spark position, the general juvenile Gong (ie, Jing Gong) reserve amount of 0.05~0.15, rough male 0.2~0.5, specific spark size can be made by master die. Copper public no processing of the dead corner, whether it is necessary to dismantle one more scattered public?. Toolpath of br/ processing of copper industry in general is: large (flat row knife) rough - knife (knife) angle #0; light use knife knife surface. Rough teachers with a flat knife is not a knife, knife with a knife after rough, then the shape of light to the number, then use knife light surface large, and small knife light surface dont plan, for some small angle and with a knife to the dead can not processing sword knife cutting range limit in order to avoid air knife, live too much. Copper Gong, especially the young male, is of higher precision, and the tolerance is usually 0.005~0.02, and the distance is 0.05~0.3. When you open the crude copper knife a knife Liu Qiu, which will shape copper rough deep a knife radius. The br/ copper is also to be processed in the middle, the table calibration, the spark discharge to