小天鹅洗衣机故障代码大全及清洗步骤(Little Swan Washing machine fault code Daquan and cleaning steps).doc

小天鹅洗衣机故障代码大全及清洗步骤(Little Swan Washing machine fault code Daquan and cleaning steps).doc

  1. 1、本文档共7页,可阅读全部内容。
  2. 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
小天鹅洗衣机故障代码大全及清洗步骤(Little Swan Washing machine fault code Daquan and cleaning steps)

小天鹅洗衣机故障代码大全及清洗步骤(Little Swan Washing machine fault code Daquan and cleaning steps) -- the Little Swan Washing machine fault code -- E1 water or water overtime, open the door cover, check the inlet valve, etc. After 6 minutes of E2 drainage, the water level sensor can not be reset, open the door cover, check the drain pipe, etc. E3 dehydration front door closed door lid closed E4 the same process, third hit the barrel to close the door cover, and the uniform distribution of clothing barrel E5 bottom voltage protection can be automatically resumed after the grid voltage is raised E6 the appointment time is not enough, press the reservation key to increase the reservation time E7 weighing correction, non empty barrel status restores empty bucket state E8 water level sensor damage or poor contact, check the water level sensor and its circuit is connected E9 automatic weighing, malfunction check, signal transmission line system assembly, if not abnormal, replace the computer board E10 does not set the current time, then set the current time, before you can set the appointment time E11 the time between now and the reservation time is too short to set the time between the present and the reservation times over the laundry time F0 power switch can not be broken, replace the power switch F2 EPROM self checking error, not removed, replace the computer board F4 zero crossing detection, line fault can not be relieved, replace the computer board F8 water level sensor damage or bad contact can not be relieved, check the water level sensor L5/LU low voltage protection can be resumed automatically after the grid voltage is raised HU high voltage protection immediately cut off the power supply and check the power supply voltage FF fail to unplug the power plug, check and repair the trouble E2: water failure, {4 minutes, the water is not discharged}: poor drainage pump, computer board drainage circuit failure Err8 ultra water level protection (water supply and drainage failure), HTD

文档评论(0)

f8r9t5c + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

版权声明书
用户编号:8000054077000003

1亿VIP精品文档

相关文档