TE后台参数解释.docx

后台参数解释1：修改特殊子帧配比ParameterID:SPECIALSUBFRAMEPATTERNS命令：LST CELL现网配置：D:SSP7/F:SSP6MOD CELL:LOCALCELLID=1,FDDTDDIND=CELL_TDD,SUBFRAMEASSIGNMENT=SA2,SPECIALSUBFRAMEPATTERNS=SSP6,EUCELLSTANDBYMODE=ACTIVE;2:BF算法开关ParameterID:BFALGOSWITCH命令：LST CELLALGOSWITCH现网配置：BfSwitch-1(室分不开）MOD CELLALGOSWITCH:LOCALCELLID=1,BFALGOSWITCH=BfSwitch-1;3.UE最大允许发射功率配置指示ParameterID:UEPOWERMAXCFGIND命令：LST CELL现网配置：配置-23MOD CELL:LOCALCELLID=1,UEPOWERMAXCFGIND=CFG,UEPOWERMAX=23;4.MIMO传输模式自适应开关ParameterID:MIMOADAPTIVESWITCH命令：LST MIMOADAPTIVEPARACFG现网配置：OL_ADAPTIVEMOD MIMOADAPTIVEPARACFG:MIMOADAPTIVESWITCH=OL_ADAPTIVE;5.修改T302、UE不活动定时器、系统内切换T304定时器命令：LST RRCCONNSTATETIMERMOD RRCCONNSTATETIMER:T302=2,T304FOREUTRAN=ms500,UEINACTIVETIMER=10;6.修改T300/T301/T310/T311/N310/N311命令：MODUETIMERCONSTMOD UETIMERCONST:LOCALCELLID=1,T300=MS1000_T300,T301=MS600_T301,T310=MS1000_T310,T311=MS1000_T311,N311=n1,N310=n20;MOD UETIMERCONST:LOCALCELLID=2,T300=MS1000_T300,T301=MS600_T301,T310=MS1000_T310,T311=MS1000_T311,N311=n1,N310=n20;MOD UETIMERCONST:LOCALCELLID=3,T300=MS1000_T300,T301=MS600_T301,T310=MS1000_T310,T311=MS1000_T311,N311=n1,N310=n20;7.修改上行时间对齐定时器现网配置：SF10240命令：MOD TATIMERMOD TATIMER:LOCALCELLID=1,TIMEALIGNMENTTIMER=SF10240;MOD TATIMER:LOCALCELLID=2,TIMEALIGNMENTTIMER=SF10240;MOD TATIMER:LOCALCELLID=3,TIMEALIGNMENTTIMER=SF10240;8.修改PUCCH算法参数（SRI轻负载门限）现网配置：0命令：MOD CELLPUCCHALGOMOD CELLPUCCHALGO:LOCALCELLID=1,SRILOWLOADTHD=0;MOD CELLPUCCHALGO:LOCALCELLID=2,SRILOWLOADTHD=0;MOD CELLPUCCHALGO:LOCALCELLID=3,SRILOWLOADTHD=0;9.BfMIMO传输模式自适应开关现网配置：MIMO_BF_ADAPTIVE命令：MODBFMIMOADAPTIVEPARACFGMOD BFMIMOADAPTIVEPARACFG:BFMIMOADAPTIVESWITCH=MIMO_BF_ADAPTIVE;10.修改TDD资源模式开关(无时钟小区激活开关)命令：MODTDDRESMODESW现网配置：OFFMOD TDDRESMODESW:CLKRESEXCLUDESWITCH=OFF;11.修改小区信道功率配置信息（物理广播信道功率/ 动态广播信道功率)命令：MODCELLCHPWRCFG现网配置：PAPB(-3/1)时-600MOD CELLCHPWRCFG:LOCALCELLID=1,PBCHPWR=-600,DBCHPWR=-600;12.BF最大复用层数（宏站和双通道室分）命令：MODCELLBF现网配置：宏站和双通道室分为双流，单通道室分为单流MOD CELLBF:LOCALCELLID=1,MAXBFRANKPARA=DUAL_LAYER_BF;MOD CELLBF:LOCALCELLID=2,MAXBFR