ADC选择最合适的基准电压源和放大器.doc

如何为您的ADC选择最合适的基准电压源和放大器 主题: 驱动精密ADC：如何为您的ADC选择最合适的基准电压源和放大器? 在线问答: [问：callhxw] 如何评定一颗ADC非线性？丢码？ [答：Jing] you can use ADCs INL and DNL parameter to evaluate the non-linearity and you can also use ENOB parameter to check code loss. Thanks!Generally ENOB releated with ADCs SNR [2006-2-28 10:32:08] [问：吉星] 在差分输入时，不考虑直流，使用差分放大器和变压器哪个更好． [答：Mariah] Transformer is better for the better noise and distortion performance, especially in very high frequencies. [2006-2-28 10:32:14] [问：Jane Yang] 请问应如何处理板级噪声对于高精度AD的影响？特别是输入部分的噪声？ [答：Jing] This is a good question and its very difficult to answer. Generally, You should consider all the input noise derived from sensor/AMP/BUFFER. You can also use a LPF to reduce the input noise. Remember the BGP of AMP should be 100x of ADCs throughput. Thanks! [2006-2-28 10:34:30] [问：石林艳] AD变换的参考基准源很重要，对模拟供电电源和数字供电电源的要求也很高吗 [答：Rui] 模拟供电电源，和数字供电电源相对基准源来说，精度要求相对较低，一般情况下用10uF的电容和0.1uF滤波即可。 [2006-2-28 10:34:31] [问：zcs_1] 请解释一下，分辨率和转换精度之间的区别 [答：Mariah] For conversion accuracy, it involves many aspecs. For example, INL, DNL, offset, gain error. [2006-2-28 10:34:46] [问：Leemour] 對不起能否講一下什麼是：RAIL TO　RAIL，這個我一直不太明白。 [答：Xiangquan] 轨到轨指输入轨到轨，或输出轨到轨，具体指的是输入信号或者输出信号的范围基本接近于电源，譬如电源是+-5V，输入信号或输出信号可以达到+-4.9几V以上 [2006-2-28 10:35:25] [问：jlwg] 很多种adi的a/d转换器件都自带有标准电压源，请问是使用器件自带的标准电压源好还是另外使用独立的标准电压源更精确？另外使用ad7710时，每次转换通道后的第一次转换结果是否是有效的？ [答：Troy] Use an independant reference to get the highest accuracy and lowest temperature drift. It depends on how much accuracy your application needs over temperature. [2006-2-28 10:37:14] [问：xwlcba] 您提到驱动AD的运放增益带宽积要求大于100倍采样速率,请问对运放的转换速率有何具体要求? [答：Troy] To get the lowest distortion (THD), we recommend using an amplifier with at least 100x gain-bandwidth product greater than the sample rate. [2006-2-28 10:39:36] [问：bly1979m] 本人最近做了一个项目用于精确测量温度的，就用到了这两种器件！请推荐几款贵司产品？并说说它的大概价格是多少？ [答：Jing] Its depend on the accuracy of your system requirement. I am pleased to recommend that you can use our ADR421+AD7799. For price, you c