CCIE LAB 第十一套题目（含要点提示）DOC - CCIE LAB.doc

CCIE LAB 第十一套 --===SUPER CCIE LAB BIBLE===-- 此份绝密档案，真实的记录了2002年11月以来的LAB新题第十一套考试全部内容。 CISCO除非特殊情况下，CCIE LAB每年只有4套内容，您参加LAB时，内容是从这4套中任意选择的。我们已经完全拥有了试验的全部内容。CCIE LAB必胜宝典的第二部分。 CCIE　LAB不像CCIE笔试一样，背完就能通过考试，它需要你的实际动手能力。你购买了我们的CCIE LAB后，必须按照上面的试验安排一步步地做实验，才能顺利通过考试。 进入实验室，一定要放轻松些。 ?若你抽到的题目和下面一样，那恭喜你了！但是，面对考官，一定要装成不知道以下的考试内容。否则，考官可能会用你事先已经知道考题的理由，把你毫不客气的赶出去。之前有过这样的先例，请记住这一点！ 以下真实的纪录的此部分的全过程 第十一套 (March ３, 2003 update) 地址分配 Use class B address range 135.YY.0.0.YY is your rack number. Vlan_A is 135.YY.57.0/24 Vlan_B is 135.YY.37.0/24 Vlan_C is 135.YY.26.0/24 Vlan_D is 135.YY.68.0/27 Dialer interface: 135.YY.35.4/30 (R5: 135.YY. 35.5，R3 : 135 . YY. 35.6) ATM interface: 192.1.YY.1/24 (ATM another IP address : 192.1. YY . 254) FrameRelay:135.YY.100.0/29 Loopback1 is 135.YY.1.1/24; Loopback2 is 135.YY.2.2/24 Loopback3 is 135.YY.3.3/24 Loopback4 is 135.YY.4.4/24 Loopback5 is 135.YY.5.5/24 Loopback6 is 135.YY.6.6/24 BB_1 is 150.100.1.YY/24 BB_2 is 150.100.2.YY/24 Unless specified above , all interface else must be 24 bit mask addressing. 一、Bridging and Switching (22分) FrameRelay （Frame relay 为full mesh，但你只能使用图中显示的PVC） config frame ralay map as mensioned on Diagram 1; use multipoint subinterface in s0/0 of R4, and cant use subinterface on any other interfaces; frame relay need be full mesh connection, but only can use PVC mensioned on Diagram 1. R4: interface Serial0/0 encapsulation frame-relay no frame-relay inverse-arp interface Serial0/0.2 multipoint ip address 40 frame-relay map ip 403 broadcast frame-relay map ip 406 broadcast no frame-relay inverse-arp 2 Catalyst 3550 config vlans on catalyst 3550 as Table 1. SW1 and SW2 has crossover link at each Fa0/24 interface.Config ISL trunk to interconnect them. Config VLANC as management VLAN, and use ip address: 135.YY.26.7/24 for VLANC routing. After finished all of configuration, SW1 and SW2 should be able to access all your network. NAME VLAN VLAN_A 30 R5 fa0/0 SW1:fa0/5 VLAN_B 50 R3 fa0/0 SW1:fa0/3 VLAN_C 20 R2