模具专业英语IV.ppt

  1. 1、本文档共43页,可阅读全部内容。
  2. 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
Chapter 4 Feed system 浇注系统 The layout of the runner system will depend upon the following factors: (i) the number of impressions, (ii) the shape of the components, (iii) the type of mould (i.e., two-plate or multi-plate mould), (iv) the type of gate. There are two main considerations when designing a runner layout. - * - The runner length should always be kept to a minimum to reduce pressure losses, and the runner system should be balanced. 流道系统的布置取决于下列因素:(1)型腔数目,(2)塑件的形状,(3)模具的类型(即,两板式或多板式模具),(4)浇口的类型。在计划一个流道布置方式时,有两个方面要重点关注。 流道的长度应该总是维持到最小,以减小压力损失,流道系统要平衡。 Chapter 4 Feed system 浇注系统 Runner balancing means that the distance the plastic material travels from the sprue to the gate should be the same for each moulding. This system ensures that all the impressions will fill uniformly and without interruption providing the gate lands and the gate areas are identical.① Figure 4.8 shows examples of moulds all based on the balanced runner principle. - * - It is not always practicable, however, to have a balanced runner system and this particularly applies to moulds which incorporate a large number of differently shaped impressions (Figure 4.10). In these cases balanced filling of the impression can be achieved by varying the gate dimensions, that is by balanced gating②. 流道平衡意味着对于每个塑件而言,塑料从主流道到浇口的流通距离应该是相同的。假如浇口的长度和截面积相同,系统要求确保所有的型腔将均匀地充满而没有阻断现象。图4.9显示了所有根据流道平衡的原则确定的例子。 可是具有平衡的流道系统并不总是可行的,尤其是组合了许多不同形状型腔的模具(图4.10)。在这些情况下,充模的平衡可以用修改浇口的尺寸来实现。即采用平衡浇口。 Chapter 4 Feed system 浇注系统 Single-impression moulds: Single-impression moulds are usually fed by a direct sprue feed into the impression and hence no runner system required. However, it may be desirable to edge gate (for example when sprue marks must not appear on the main surface) in which case a short runner as shown in Figure 4.8a may be used. But note that by gating a single impression in this way the impression itself must be offset. This is undesirable, particularly with a large impression, as the injection pressure will ex

文档评论(0)

wxc6688 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档