FREQTIS.doc lcp--pps介绍.doc

FREQTIS?的成形技术Molding technology for FREQTIS ◆ Freqtis? 的注射成型Injection Molding of FREQTISFreqtis? 分为基于 LCP 的等级和基于 PPS 的等级两种。：FREQTIS? includes two grades, one grade based on LCP and one based on PPS. 下面介绍 Freqtis? 的成型条件（按基础树脂分项说明） Here, the following introduces the molding conditions of FREQTIS? and provides a separate description for each base resin depending on item LCP 基 PPS 基 C0511A C0711A P0813A P1210A P2020A 机筒温度 ?后部 320～325℃ 290～300℃ ?中部 325～335℃ 300℃ ?前部 335～345℃ 310℃ ?喷嘴 320～350℃ 310～320℃ ?模具温度 70～150℃ 135～150℃ LCP base PPS base C0511A C0711A P0813A P1210A P2020A Cylinder temperature ?Rear part 320 - 325℃ 290 - 300℃ ?Middle part 325 - 335℃ 300℃ ?Front part 335 - 345℃ 310℃ ?Nozzle 320 - 350℃ 310 - 320℃ ?Mold temperature 70 - 150℃ 135 - 150℃ 预干燥Preliminary dryingFreqtis?几乎不吸湿，但为了改善其外观并防止流涎和劣化，建议进行预干燥处理。Although FREQTIS? hardly absorbs moisture, we recommend preliminary drying in order to improve the appearance of mold products and to prevent drooling and deterioration. 推荐条件：Recommended conditions:温度：140～160℃时间：4～6 小时Temperature: 140 to 160℃Time: 4 to 6 hours 机筒温度Cylinder temperature推荐条件如下：Recommended conditions are described.◇ C0511A, C0711A（LCP 基）◇ C0511A, C0711A (LCP base)后部：320～325℃Rear part: 320 - 325℃ 中部：325～335℃Middle part: 325 - 335℃ 前部：335～345℃Front part: 335 - 345℃ 喷嘴：320～350℃Nozzle: 320 - 350℃ 勿使树脂温度超过 360℃。Do not set the resin temperature to 360℃ or more. 极限滞留条件：30分钟×350℃ Limit residence in cylinder condition: 30 min x 350℃◇ P0813A, P1210A（PPS 基）◇ P0813A, P2110A (PPS base)后部： 290～300℃Rear part: 290 - 300℃ 中部： 300℃Middle part: 300℃ 前部： 310℃Front part: 310℃ 喷嘴： 310～320℃Nozzle: 310 - 320℃ 因产品形状而需要高流动性时，也可将上述温度调高 20℃ 左右。If high flowability is required depending on the product shape, the temperature can be lowered by approximately 20℃ less than the above.模具温度. Mold temperature推荐条件如下：Recommended conditions are described.◇ C0511A, C0711A（LCP 基）C0511A, C0711A (LCP base)70～150℃为了改善成型品外观并确保流动性，建议尽可能在较高的模具温度下进行成型。In order to i