mold_flow_checklist_解释说明.ppt

  1. 1、本文档共22页,可阅读全部内容。
  2. 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
mold_flow_checklist_解释说明

Enter fill/pack switchover percentage for each scenario 填充/保压转换时填充百分率 Enter maximum pressure at end of fill for each scenario 第一阶段注射压力 Review pressure distribution and balance at end of fill for each scenario 压力分布及填充平衡 Enter flow front temperature variation at end of fill for each scenario 前端温差 Enter bulk shear rate in gate for each scenario 浇口处剪切率 Enter shear stress in the part for each scenario 填充末端(95%时)壁上剪切力 Review weld lines and include temperature at flow front for each scenario 熔界线位置和长度包括熔接线位置的前端温度 Review air traps for each scenario 气泡 Enter pack and hold pressure for each scenario 第二阶段压力 Review injection pressure at nozzle versus time for each scenario 喷嘴处压力/时间图 Enter pack and hold time for each scenario 第二阶段(保压)时间 Enter maximum clamp tonnage required for each scenario 最大锁模力 Review and enter volumetric shrinkage at ejection for each scenario 顶出时的体积收缩量 Enter sink mark depth value for each scenario 最大缩印深度值 Enter cavity and core coolant flow rate required for turbulence for each scenario 型腔及型芯冷却水流动速率,保证是湍流水 Enter cavity and core mold wall temperature range for each scenario 型腔壁上温差(模温) Enter cavity and core mold wall temperature range for each scenario 型腔型芯最大模温差 Enter temperature rise in coolant for cavity and core for each scenario 型腔及型芯进出水温差 Enter circuit Reynolds number for cavity and core for each scenario 型腔及型芯最小雷诺数 Enter X-Deflection values for each scenario X方向变形最大绝对值 Enter Y-Deflection values for each scenario Y方向变形最大绝对值 Enter Z-Deflection values for each scenario Z方向变形最大绝对值 * This plot shows the pressure distribution at 97% switchover by volume. Pressure to fill – 8,675 psi. 97% JES3.2—Analyze Mold Flow and Select Optimal Scenario通过模流分析选择最佳方案 This plot shows the pressure distribution at 97% switchover by volume. Pressure to fill – 8,675 psi. 8675.6 Avoid Good Part is poorly balanced and has large distribution of pressure 产品填充不平衡且压力差较大 Part is very well balanced and has small distribution of pressure 产品填充平衡且压力分布均匀 Co

文档评论(0)

cgtk187 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档