平面度不良对策报告_8d报告案例.docxVIP

  1. 1、本文档共2页,可阅读全部内容。
  2. 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  5. 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  6. 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  7. 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  8. 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
Approved made Wang Liu To: STT-A Fax: ATTN: CC: Phone: Date: 2015-5-6 RE: win deformation causing Flotaing on Board 山于产品不良给贵司带来的麻烦深表歉意,收到贵司的信息后,我们立即展开调查。 Very sorry for the defect makes you getting in trouble, while received your information, we investigated the matter immediately 反馈日: 2011-3-3 Feedback date: 2011-3-3 品 名: l?842?700?H ITEM NO: 1-842-700-11 不良内容:组品平面度不良 Defect content: Pre-case founded win deformation causing floating on board 不良率: 7% Defect rate: 7% 発生原因(happen reason) 根据客户寄送的不良样品,内部用PCB板进行了确认。 标示平面度在o?6mm以下所有样品,插入PCB后均没有翘起,是0K品。 标示平面度超过0?6mm的所有样品,框架面明显变形,插入PCB后均有明显翘起, 而且不能插入插板。 框架面变形推定发生原因之一可能为工序中拿取不注意导致。工序F插座钏装或插 板检验时拔取不规范可以再现类似的产品变形。 另外还有可能为落下品混入。 board. board. Confirm result: The marked un-flatness of the parts below 0.6mm seems no obvious gap between the parts and PCB. It is OK parts. The marked un-flatness of the parts over 0.6mm bent obviously,the gap is very obvious between the parts and PCB after inserting into the PCB We think the bent maybe caused for the careless when the part was take out from die jig in the caulking process? They can be reappeared for the abnormal operation when drawing off the parts in the F connector caulking or jig check process ? And also maybe it is the defect parts mixed which had been dropped to the floor before. 流出原因(outflow reason): 该产品的平面度没有在图纸上明确定义,因此内部并无列入管控。另外平面度小于 0. 6mm的实际为0K品。 平面度大于0. 6mm (实际为变形所致)的产品 检查员漏检 可能插板插入后拔出不良,所以后续未有检验导致流出。 1 ? For the flatness of parts has not been identified in the drawing, so We did not control in our process, and also actual the flatness below 6.6mm is ok after assemble with JIG? 2. the flatness of the parts over0.6 mm Maybe the inspector miss-check it it deformed when the parts were picked out from the jig by the inspector for the abnormal operation, then we pack it without check. So It flows out. 発生对策(happen countermeasure): 跟SONY HQ制定平面度小于0.6mm为OK品的平面度标准并追加进图纸,我们内部制 程进行管控。 教育作业员注意工序中的取用,按作业指导书垂直或两手水平拔取防止变形。 1 ? Make the flatness standard with SONY HQ and identify the st

文档评论(0)

2105194781 + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档