DZT 0101.3-1994地质仪器仪表制造时间定额 刨床.pdf

DZ中华人民共和国地质矿产行业标准DZ/T 0101.3—94地质仪器仪表制造时间定额刨床1994-01-27发布1994-12-01实施中华人民共和国地质矿产部发 布 自次主题内容与适用范围·12代号及含义··.3定额时间的组成和计算时间定额的使用方法刨切削准终、装卸、布休和辅助时间定额5刨碳素钢平面、直槽时间定额刨碳素钢直槽时间定额(14 刨加工切断45°坡口时间定额( 34 )刨加工V型槽和曲面时间定额9(36’附录 A索(参考件）·44) DZ/T 0101.3—94115135155175195225255285315345385425465495.545595120140160180200230260290320350390430475500550600间5.05.86.67.58.39.510.812.013.314.516.217.819.720.722.824.97.58.49.410.311.212.614.115.516.918.320.222.124.225.427.730.16.98.19.210.411.613.315.016.818.520.222.524.927.528.931.834.79.711.012.313.614.916.918.920.822.824.827.33.034.637.941.210.011.713.315.016.719.221.724.226.729.232.535.839.641.745.850.013.215.16.920.723.626.429.232.134.!38.742.546.749.153.858.614.516.927.731.334.938.642.247.051.857.260.266.372.318.221.029.233.337.441.545.649.755.160.666.870.277.083.920.323.730.533.939.044.49.254.259.366.172.980.584.793.2101.724.928.740.346.151.857.663.476.884.593.298.0107.6117.229.339.043.948.856.163.470.778.085.495.1104.91115.9 1122.0134.1146.337.940.651.657.265.573.882.190.4109.8120.9133.3139.7154.1167.91.613.5.6.3 DZ/T 0101.3—946.3刨碳素钢垂直面时间（见表8）。表切进加工高度计加15205次削给I:程h算长长次乘深量进度计算高度度度给量时间分类L1nsTo0.50.81.11.4100707318.3TM1.72.02.32.6T.0.81.11.51.918015052.513.1TM1.92.42.83.2To1.11.62.22.728025036.59.1TM2.32.93.64.22.5-~3.00.25T。1.62.43.24.0380350256.3TM2.93.84.75.6T。:2.23.34.45.648045017.94.5TM3.64.86.17.4To3.24.86.58.165062012.53.1TM4.76.58.410.21.步辅助时间布休时间百分比粗糙度10 DZ/T 0101. 3--94253035404555657585115135155303540455060708090100120140160间1.61.92.22.52.73.38°4.41.95.56.67.78.72.93.23.53.84.24.85.46.06.67.38.59.711.02.32.73.13.43.84.65.36.16.97.69.210.712.23.74.14.55.05.46.37.18.08.69.711.513.214.93.33.85.56.67.78.89.911.013.215.417.64.85.46.06.77.38.59.811.012.313.516.018.521.04.85.66.37.17.99.511.112.714.315.919.022.225.46.57.48.39.210.111.913.715.517.319.122.726.329.96.77.88.910.011.113.315.617.820.022.226.731.135.68.69.911.112.413.916.218.721.223.826.331.336.441.49.711.312.914.516.119.422.625.829.032.338.745.251.612.013.