四川理工机械原理课程设计凸轮设计 C语言程序.pdfVIP

#includestdio.h

#includemath.h

#includestdlib.h

#definepi3.1415926

#definee20

#defineh50

#definer60

#definer110

main()

{

inta,i;

doubles,s0,x,y,x1,y1,a0,a1,a2,a3;

doubleb,b1,b2,c1,c2;doubleb,b1,b2,c1,c2;

请输入起始角度和间隔角度请输入起始角度和间隔角度请输入起始角度和间隔角度

for(a;a=360;a=a+i)

{

a0=a*pi/180;

s0=sqrt(r*r-e*e);

if(a=0a=120)

{

a1=120*pi/180;a1=120*pi/180;

b=h/a1-h*cos(2*pi*a0/a1)/(a1);

}

if(a120a=150)

{

a1=30*pi/180;a1=30*pi/180;

b=0;

}

if(a150a=240)

{

a0=(a-150)*pi/180;

a1=90*pi/180;

b=-h*pi*sin(a0*pi/a1)/(2*a1);

}

if(a240a=360)

{

a1=120*pi/180;a1=120*pi/180;

b=0;

}}

b1=(s0+s)*cos(a0)+b*sin(a0)-e*sin(a0);

b2=-(s0+s)*sin(a0)+b*cos(a0)-e*cos(a0);

c1=b1/sqrt(b1*b1+b2*b2);

c2=-b2/sqrt(b1*b1+b2*b2);

}

}

请输入起始角度和间隔角度0

2

a=0s=0.000000x=20.000000y=56.568542x1=16.666667x2=47.140452

a=2s=0.001522x=21.962083y=55.837614x1=18.320969x2=46.524060

a=4s=0.012158x=23.898151y=55.047743x1=19.991419x2=45.842449

a=6s=0.040921x=25.807738y=54.208782x1=21.676679x2=45.101951

a=8s=0.096626x=27.691628y=53.330245x1=23.376441x2=44.309205

a=10s=0.187793x=29.551789y=52.421116x1=25.091319x2=43.471021

a=12s=0.322554x=31.391276y=51.489655x1=26.822678x2=42.594268

a=14s=0.508561x=33.214115y=50.543232x1=28.572413x2=41.685772

a=16s=0.752908x=35.025167y=49.588168x1=30.342688x2=40.752196

a=18s=1.062047x=36.829962y=48.629608x1=32.135652x2=39.799917

a=20s=1.441722x=38.634531y=47.671415x1=33.953172x2=38.834850

a=22s=1.896903x=40.445218y=46.716085x1=35.796610x2=37.862248

a=24s=2.431733x=42.268483y=45.764701x1=37.666675x2=36.886448

a=26s=3.049482x=44.110702y=44.816903x1=3